STL Weight, Centre of Mass & Moment of Inertia Calculator Community
Questions, answers and tips from people who use the STL Weight, Centre of Mass & Moment of Inertia Calculator. Exact volume, mass, centre of gravity and inertia tensor of any STL, OBJ, 3MF or STEP model.
Ask a question about STL Weight, Centre of Mass & Moment of Inertia Calculator
Anyone can read this page. To ask a question, reply or vote, please log in. It takes under a minute.
Log in to askNo questions yet. Yours can be first.
This page shows only real posts from real people, so it starts empty. The guide below has the questions people most often have about the STL Weight, Centre of Mass & Moment of Inertia Calculator. Pick one to start a thread, or write your own.
From the tool guide: common questions about STL Weight, Centre of Mass & Moment of Inertia Calculator
The items below are not posts by community members. They come from the written guide for this tool and are here to get a conversation started. Use “Ask a follow-up” to open a thread about any of them.
Is the centre of mass exact?
Yes for the mesh as given, assuming uniform density.
From the tool guide Ask a follow-upAre units millimetres?
Choose the file units and results are converted to mm, g and g·mm².
From the tool guide Ask a follow-upDoes it handle several parts?
Multiple shells are treated as one solid with a shared centre of mass.
From the tool guide Ask a follow-upIs my file uploaded?
No — all processing happens in your browser.
From the tool guide Ask a follow-upWhat this tool does
Knowing where a part balances matters for drones, rotating parts, robot arms, counterweights and anything you hang or spin. This tool reads a closed 3D model and computes its exact volume, mass in a chosen material, centre of mass and the full 3 × 3 inertia tensor, then diagonalises it to give the principal moments and axes. The centre of mass is marked with a red sphere in the viewer.
How to use it, step by step
- Drop in an STL, OBJ, 3MF or STEP file.
- Set the file units and choose a material.
- Read mass, centre of mass and inertia from the table.
- Tick the marker box to see the centre of mass in the model.
Tips from the guide
- Repair the mesh first if it is not watertight — holes change the volume.
- Pick the right file units; inches vs millimetres is the most common error.
- Use the principal moments for rotating-part balance and vibration checks.
- Printed weight depends on slicer settings; treat it as ±15%.
Common mistakes to avoid
- Using a surface-only model with holes and trusting the volume.
- Entering density in kg/m³ instead of g/cm³.
- Forgetting hollow models: an STL of a hollow part counts the shell only if the inner cavity is modelled.
Who uses it
- Drone and robot builders. Find the balance point before flying or mounting.
- Mechanical engineers. Inertia values for simulation and motor sizing.
- 3D printing users. Predict filament use and part weight.
- Students. Check hand calculations of centroids and inertias.
How to ask a question people can answer
A good thread on the STL Weight, Centre of Mass & Moment of Inertia Calculator saves everyone time. Start with a title that names the exact problem, such as the input you used, the result you expected and the result you got. A title like “Not working” is hard to answer, while a title with the specifics gets replies quickly.
- Say what you tried. List the steps you followed and any settings you changed, so replies do not repeat what you already did.
- Share a small example. A short sample input and the output you saw is worth more than a long description. Remove anything private first.
- Mention your setup. Your device, browser and whether you are on a phone or a computer can explain many odd results.
- One question per thread. Separate topics get clearer answers and are easier to find later with the search box above.
- Come back and reply. If a suggestion worked, say so and upvote it, and if you found the fix yourself, post it for the next person.
Community rules
Be kind, stay on topic and keep personal data out of your posts. Do not post adult, hateful or illegal content, advertising or repeated links. Every post is shown with its author’s username and date, and posts that break these rules can be hidden by moderators. This space is for help with the STL Weight, Centre of Mass & Moment of Inertia Calculator and related tasks, and it is separate from the sitewide discussion forum where broader topics live.